How to restore and decorate a facade with lime-based products?

Home - Issues and Solutions - Outdoor Solutions - Restaurare o decorare facciata con prodotti a base di calce

  • SOLUTION A: Smooth finishes for brush application.

    CYCLE

    INDICATIVE QUANTITY OF
    MATERIAL PER SQM

    1

    Treatment with ready-to-use brush-applied BIOCID solution, waste, ready for use. After at least 24 hours from application, proceed with mechanical cleaning of the surfaces. The formulation can be applied on both pre-painted and non-pre-painted supports.

    10 SQM/L

    2

    Completely remove any traces of old paints or old coatings. Wash with high-pressure water, brush or scrape the entire facade, cleaning it from any flaking or detaching paints, removing any dirt or dust.

    3

    In case of particularly flaking supports, apply a coat of water-based penetrating FIXACRIL fixative suitably diluted to leave the support absorbent.

    10 - 15 SQM/L

    4a

    In the case of repaired plasters, shave the entire surface with PAULINSANA RAS R550 low elastic modulus anti-cracking smoothing plaster for old plasters and wait for 10 days.

    1.1 KG/SQM
    PER MM OF THICKNESS

    4b

    Make any smoothing with a specific breathable smoothing plaster based on hydraulic binders RC 618 in powder form.

    1.2 KG/SQM
    PER MM OF THICKNESS

    5

    Apply two coats of cross-brush applied MARMOLADA FINISH lime-based wall paint, coloring earth, micronized loads and various additives.

    0.20 KG/SQM

    SOLUTION B: Rustic or textured finishes with thickness.

    CYCLE

    INDICATIVE QUANTITY OF MATERIAL PER SQM

    1

    Treatment with ready-to-use BIOCID solution applied with a brush to refuse,
    ready to use. After at least 24 hours from the application, proceed
    with mechanical cleaning of the surfaces. The formulation can be
    applied on both pre-painted and unpainted surfaces.

    10 SQM/L

    2

    Completely remove any traces of old paints or old coatings.
    Pressure wash, brush, or scrape the entire facade cleaning it from any
    flaking or detaching paints, eliminating any trace of dirt or dust.

    3

    If the surfaces are particularly flaking, apply a
    FIXACRIL water-based fixative with strong penetration
    appropriately diluted to leave the absorbent support.

    10 - 15 SQM/L

    4a

    In the case of patched plaster, skim coat the entire surface with
    PAULINSANA RAS R550 low modulus elastic skim coat for old plasters and wait 10 days.

    1.1 KG/SQM
    PER MM OF THICKNESS

    4b

    Carry out any smoothing with specific breathable plaster based on hydraulic binders
    RC 618 in powder form.

    1.2 KG/SQM
    PER MM OF THICKNESS

    5

    Lightly moisten the support a few hours before applying the final coating.

    6

    Apply with a steel trowel and finish with a sponge float
    with MARMOLADA 70/100/120. Mineral plaster
    composed of lime putty, coloring earths, and siliceous aggregates.

    2.5 - 3 KG/SQM - 70
    3 - 3.5 KG/SQM - 100
    3.5 - 4 KG/SQM - 120

    SOLUTION C: Smooth marmorino finishes with thickness.

    Translate the following sentence into English:

    CYCLE

    INDICATIVE QUANTITY OF MATERIAL PER SQM

    1

    Treatment with BIOCID solution applied with a brush to refuse,
    ready for use. After at least 24 hours from the application, proceed
    with the mechanical cleaning of the surfaces. The formulated can be
    applied both on pre-painted and unpainted supports.

    10 SQM/L

    2

    Completely remove any traces of old paints or coatings.
    Power wash, brush, or scrape the entire facade to clean it from any
    flaking or peeling paints, eliminating any dirt or dust.

    3

    In case of particularly flaking supports, apply a
    FIXACRIL water-based fixative with strong penetration
    diluted appropriately in a way that leaves the absorbent support.

    10 - 15 SQM/L

    4

    For patched plaster, coat the entire surface with
    PAULINSANA RAS R550 low-modulus elastic skimming plaster for old plasters and wait 10 days.

    1.1 KG/SQM
    PER MM OF THICKNESS

    5

    Slightly moisten the surface a few hours before the application of the final coating.

    6a

    Apply two coats with a steel spatula of MARMORAS smooth marble wall coating, consisting of modified lime plaster, stable inorganic pigments and marble powder.

    2 - 2.5 KG/SQM
    IN TWO COATS

    6b

    To achieve finishes like smoothed lime with marbling semi-gloss effect, apply over MARMORAS two or more coats of lime stucco consisting of lime plaster, natural coloring earths, and inert mineral fillers, MARMOLADA ANTICO.